Search:

Type: Posts; User: nizak

Page 1 of 8 1 2 3 4

Search: Search took 0.66 seconds.

  1. Replies
    10$$
    Views
    345

    Good thought. 20' ft of 10/2 NM stubbed from...

    Good thought. 20' ft of 10/2 NM stubbed from basement to garage attic would be money well spent.
  2. Replies
    10$$
    Views
    345

    Home shop equipment

    Would like opinions on the following.
    I am doing the electrical on a new residential build.Owner tells me that she will be using a portion of the garage for woodworking. There are a variety of...
  3. Thread: 6/3 nm-b

    by nizak
    Replies
    7$$
    Views
    380

    6/3 nm-b

    Is it code compliant to install a 60amp breaker on 6/3 nm-b cable? The application is an indoor hot tub and the mfg's install sheet says 60amp circuit required. I know with certainty that a 50amp...
  4. Replies
    7$$
    Views
    300

    Has your customer contacted the utility. Maybe...

    Has your customer contacted the utility. Maybe they could achieve a 10% boost within the xfmr serving the residence. Seems what you are proposing would be quite expensive. Just a thought.
  5. Thread: noisy bath fan

    by nizak
    Replies
    9$$
    Views
    449

    Found the culprit today with the noisy fan. I...

    Found the culprit today with the noisy fan. I went up in the attic and found that the 4" flex duct had gotten wedged into one of the truss crotches. It was a sharp 90 deg bend and restricted by at...
  6. Thread: noisy bath fan

    by nizak
    Replies
    9$$
    Views
    449

    Will install noisy motor/impeller assembly in one...

    Will install noisy motor/impeller assembly in one of the other housings and see what happens.
  7. Thread: noisy bath fan

    by nizak
    Replies
    9$$
    Views
    449

    noisy bath fan

    Anybody here know much about ducting creating excessive fan noise?

    I have 4 newly installed QT series bath fans. All are 80 cfm, same model,same mounting means,and same diameter flex duct.3 of...
  8. Replies
    3$$
    Views
    222

    LED lamps and dimmers

    I am looking for help in finding a LED lamp and compatible dimmer. Application will be 6" Halo ICAT housing. An equivalent to a 65W R30 flood is what I would like. I have tried several manufacturer...
  9. Replies
    8$$
    Views
    483

    kitchen lighting retro

    Looking for some suggestions on the following job.

    I have an existing kitchen that has upper level living space above(no attic access). General contractor wants me to quote installing recessed can...
  10. Replies
    2$$
    Views
    200

    Indoor hydromassage tub

    Are enclosed recessed can trims required over hdromassage bath tubs? If so, could you post the article# Thanks.
  11. Replies
    10$$
    Views
    724

    grid ceiling fixture mount

    Does anyone here have a problem with the ceiling tile wanting to raise up in the grid when installing a surface mount fixture? Using a Caddy 512 for instance.I always end up having to wedge something...
  12. Replies
    9$$
    Views
    405

    The hour was a bit of an exaggeration. I'm sure...

    The hour was a bit of an exaggeration. I'm sure half of that the time was spent bitching to the G/C about letting the excavator install PVC when a phone call could have had me there in 30 minutes.
  13. Replies
    9$$
    Views
    405

    voltage drop question

    I have a 120v sewage pump that is located in an outside tank system. The system has 3 floats and a 1hp pump. The remote exterior control panel nameplate is telling me to figure the pump draw at 16...
  14. Replies
    11$$
    Views
    503

    Is the requirement for GFI on the fans for...

    Is the requirement for GFI on the fans for personal protection? If so, it would seem that more people would be standing in the tub or shower replacing a lamp(quite possibly with the switch on) then...
  15. Replies
    11$$
    Views
    503

    GFCI protection for shower cans

    Was there ever a NEC requirement for GFCI protection of recessed can lights above a shower or tub? I know that bath fans installed over a tub or shower have a manufacturers requirement for GFCI...
  16. Replies
    2$$
    Views
    221

    Would vinyl be considered a "combustible surface"?

    Would vinyl be considered a "combustible surface"?
  17. Replies
    2$$
    Views
    221

    HID wall pak installed on vinyl siding

    I was talking to a building owner today and he asked about installing wall pak lighting around the perimeter of a building that is vinyl sided. Is there any code that prohibits installing HID type...
  18. Replies
    1$$
    Views
    174

    Commercial space renovation

    I am looking into doing some renovation work on a small 4 tenant commercial space. The structure is an older large home that over time has been crudely divided into 4 small commercial spaces.Each...
  19. Replies
    12$$
    Views
    637

    oven disconnecting means

    Would like some thoughts on disconnecting means for double wall oven. Ovens come factory installed with FMC installed for wiring into a j box. FMC is only long enough to get to a j box located in...
  20. Replies
    16$$
    Views
    780

    Time clock vs contactor

    I need to install a 240 V heater (5kw). Owner wants it on a timer so that it only runs at a particular time in the early morning hours.I am debating if I should use a DP/ST time clock(T104) or...
  21. Looks like there may have been a "bar type"...

    Looks like there may have been a "bar type" fixture installed with what appear to be hollow wall anchors.If the NM cable can terminate with an approved connector inside the channel space of the...
  22. Replies
    12$$
    Views
    817

    vinyl siding blocks

    I have 2 siding contractors I work with and they both install 1" deep vinyl mounting blocks for exterior lighting.I will stub nm out and they set the block and pull wires thru. I cut out box opening...
  23. Replies
    45$$
    Views
    1,836

    water tank bonding jumper

    Is it a code requirement to bond between the hot and cold water lines on a hot water tank? If yes, could someone give me the specific language.

    Thanks.
  24. Replies
    11$$
    Views
    544

    help sizing an electric heater

    Is anyone here familiar with the sizing of a fan forced electric heater for a garage?

    Here are the particulars:
    - 11ft ceilings
    -650 sq ft
    -R19 insulation/finished drywall
    -maintain 45 degree...
  25. Replies
    3$$
    Views
    263

    hanging fixture height

    Does anyone have any suggestions on what height to hang a chandelier in a foyer with 19' ceilings. Most times there is a window that I center the fixture in so it can be seen from the outside, not so...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4