Search:

Type: Posts; User: ActionDave

Page 1 of 8 1 2 3 4

Search: Search took 0.33 seconds.

  1. Replies
    27$$
    Views
    860

    It's not about the paperwork, it's about GE...

    It's not about the paperwork, it's about GE getting a code change because their dishwashers suck instead of recalling them.
  2. Replies
    27$$
    Views
    860

    Yes who might be more accurate....or is it whom?...

    Yes who might be more accurate....or is it whom? I can never remember.
  3. Replies
    6$$
    Views
    260

    I don't think the OP is asking about "how current...

    I don't think the OP is asking about "how current flows?". I think he is looking for some tips about how to read a diagram or schematic. If that he is not what he means I don't care, since I suck...
  4. Replies
    19$$
    Views
    457

    You are welcome to dinner at my table any time.

    You are welcome to dinner at my table any time.
  5. Replies
    27$$
    Views
    860

    What is it that GE knows that the automobile...

    What is it that GE knows that the automobile manufacturers don't?
  6. Replies
    11$$
    Views
    365

    arion

    There was a member that posted on this forum a year or two ago about some power quality problems that were very dramatic and it was defiantly the power company's fault and if they would not fit he...
  7. Replies
    19$$
    Views
    457

    I agree. He can't just rip a page out of the...

    I agree. He can't just rip a page out of the codebook and throw it away 'cause he doesn't like it. He is an electrical inspector, not Judge Roy Bean.
  8. Replies
    31$$
    Views
    803

    So unfold the wire, pull it through and tighten...

    So unfold the wire, pull it through and tighten the lug and you are good to go. How far is it from the j box to the panel?

    Probably won't even loose access to the screw terminals.
  9. Replies
    4$$
    Views
    273

    There is some old stuff that I have ripped out...

    There is some old stuff that I have ripped out that has SQ D on the dead front and Westinghouse on the innards that look just like your pic. I can't remember the numbers on the breakers. I'll try and...
  10. Replies
    14$$
    Views
    318

    No.

    No.
  11. Replies
    31$$
    Views
    803

    Then just land the #4 in the big hole without...

    Then just land the #4 in the big hole without bending it over, #4 has to be in the range it is listed for.
  12. Replies
    3$$
    Views
    151

    Washington has some special rules but since you...

    Washington has some special rules but since you have access to the footer I would see if he would sign off on 20' of #4 encased in concrete down at footer level rather than chipping into the...
  13. Replies
    31$$
    Views
    803

    Are you sure the big hole doesn't have a range of...

    Are you sure the big hole doesn't have a range of wire sizes up to 1/0 listed on it? It would have to be one honkin' big ground bar to have 1/0 as the smallest conductor listed on the wire sizes.
  14. I would run what we call mobile home feeder wire....

    I would run what we call mobile home feeder wire. It's 2,2,4,6 gauge AL and is priced less than buying the individual conductors and would work just fine for the application IMO.
  15. No you are not reading it right. 250.118 (2),...

    No you are not reading it right. 250.118 (2), (3), (4) are most likely what applies.

    The only way (5) would apply is if you are using flex or sealtite and that is where (a), (b), (c) and (d) are...
  16. 250.118 If the conduit qualifies as an EGC I...

    250.118

    If the conduit qualifies as an EGC I would not see a problem using it either.
  17. Replies
    23$$
    Views
    638

    I agree.

    I agree.
  18. Thread: Chlorine?

    by ActionDave
    Replies
    6$$
    Views
    292

    I have no doubt they are disintegrating. What are...

    I have no doubt they are disintegrating. What are they there for?
  19. Replies
    26$$
    Views
    638

    True. The .39 cent bulk specials at the home...

    True. The .39 cent bulk specials at the home center or supply house are junk. Full disclosure, I have them all over my house, but the highest load device that I have plugged in is a water cooler. I...
  20. Replies
    10$$
    Views
    239

    Emphasis added on Branch Circuit... again I...

    Emphasis added on Branch Circuit...
    again I agree.
  21. Replies
    26$$
    Views
    638

    Well you need a new recpt now for sure. I think...

    Well you need a new recpt now for sure. I think there is a loose connection to the old one. I don't think you need a 20A recpt.
  22. Replies
    26$$
    Views
    638

    Did you pull anything apart? I think the problem...

    Did you pull anything apart? I think the problem could easily be with a connection to the recpt as it could be with what was plugged into it.
  23. Replies
    10$$
    Views
    239

    I agree.

    I agree.
  24. Replies
    28$$
    Views
    743

    If it is set up for bottom feed there ought to be...

    If it is set up for bottom feed there ought to be something indicating the utility and load side meter lugs.
  25. Replies
    11$$
    Views
    321

    Can't say for sure it applies to phone wires but...

    Can't say for sure it applies to phone wires but 300.19 allows a hundred feet between vertical supports for electrical conductors so I think you are okay.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4