Search:

Type: Posts; User: infinity

Page 1 of 8 1 2 3 4

Search: Search took 1.76 seconds.

  1. Replies
    8$$
    Views
    161

    IMO the general feeling is that rods are pretty...

    IMO the general feeling is that rods are pretty poor electrodes anyway so it doesn't really matter how they're connected. Further proof is that as long as you have two rods their resistance could be...
  2. Replies
    11$$
    Views
    275

    What kind of blocks are they using?

    What kind of blocks are they using?
  3. I might use PVC jacketed MC in a shallow chase...

    I might use PVC jacketed MC in a shallow chase covered with some sort of patching material.
  4. How do you define the "quality" of the ground? ...

    How do you define the "quality" of the ground? For the home's electrical system the main bonding jumper will provide a connection between the EGC's and the system neutral that's the one that really...
  5. Also as Augie stated the SSBJ can be a suitable...

    Also as Augie stated the SSBJ can be a suitable metallic raceway.
  6. Thread: ON egc

    by infinity
    Replies
    3$$
    Views
    202

    What's the wiring method? Around here many...

    What's the wiring method? Around here many houses wired in 1960 would have AC cable which would have an EGC.
  7. Replies
    6$$
    Views
    171

    If you're using EMT then the minimum needed could...

    If you're using EMT then the minimum needed could be three, HOT, SW LEG, SW LEG.
  8. Replies
    20$$
    Views
    1,170

    Tie in points for fall protection equipment need...

    Tie in points for fall protection equipment need to be rated for a minimum of 5000#'s. That one is not even close. :)
  9. Thread: PINK WIRE

    by infinity
    Replies
    22$$
    Views
    853

    The question wasn't from the NEC since the word...

    The question wasn't from the NEC since the word pink does not exist in that document.
  10. Thread: PINK WIRE

    by infinity
    Replies
    22$$
    Views
    853

    True or False: A pink or purple conductors be...

    True or False:

    A pink or purple conductors be used as an ungrounded conductor?
  11. Replies
    28$$
    Views
    744

    Since they're all on one switch than IMO it's a...

    Since they're all on one switch than IMO it's a continuous load because they can be on at maximum ampacity for three or more hours. My wife leaves the basement lights on for days at a time. :roll:
  12. Thread: 250.148

    by infinity
    Replies
    13$$
    Views
    395

    I've mentioned this before but does the NEC...

    I've mentioned this before but does the NEC really want use to connect all of the EGC's together, even in a large feeder pull box that may have multiple sets of say 20-#3/0 EGC's?
  13. Replies
    28$$
    Views
    744

    How did you calculate the total load? Will these...

    How did you calculate the total load? Will these all be on one switch?
  14. Replies
    1$$
    Views
    127

    The conductors between the MCC and the disconnect...

    The conductors between the MCC and the disconnect are as you've stated tap conductors therefore the tap rules would apply. You could just change the 200 amp fuses to 100 amps and eliminate the tap...
  15. Replies
    19$$
    Views
    612

    I've done a few additions where the rebar in the...

    I've done a few additions where the rebar in the footing was #3 or 3/8".
  16. Replies
    6$$
    Views
    281

    334.15(C) if this is in an unfinished basement or...

    334.15(C) if this is in an unfinished basement or crawl space.
  17. Replies
    19$$
    Views
    612

    Unless told otherwise I would pound in two rods...

    Unless told otherwise I would pound in two rods and be done with it.
  18. Replies
    17$$
    Views
    508

    Even in basements? ;)

    Even in basements? ;)
  19. Replies
    3$$
    Views
    202

    The 2014 NEC will likely be adopted in the spring...

    The 2014 NEC will likely be adopted in the spring of 2015 when the triennial license renewal period ends. Not sure about NFPA-72.
  20. Replies
    9$$
    Views
    523

    Have you paid for one of her webinars?

    Have you paid for one of her webinars?
  21. Replies
    3$$
    Views
    278

    Just to clarify the driver is within the fixture?...

    Just to clarify the driver is within the fixture? If so then the fixture needs an EGC, if the manufacturer used the EGC in the cord for something else then the fixture is not properly wired,...
  22. Replies
    2$$
    Views
    347

    I would add that the cord grip fitting is not...

    I would add that the cord grip fitting is not listed for the use shown in the photo's.
  23. Thread: Flex bond

    by infinity
    Replies
    14$$
    Views
    466

    Gas:

    Gas:
  24. Replies
    59$$
    Views
    1,220

    I agree, if you got hit off of a ballast neutral...

    I agree, if you got hit off of a ballast neutral that had a 1/4 amp load then that would be the maximum current of you and the ballast in series.
  25. Replies
    10$$
    Views
    375

    Here's the requirement from Article 440, within...

    Here's the requirement from Article 440, within sight unless it meets the exceptions:
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4