Search:

Type: Posts; User: DAWGS

Page 1 of 8 1 2 3 4

Search: Search took 0.33 seconds.

  1. Replies
    6$$
    Views
    844

    Thanks for the replies fellas.

    Thanks for the replies fellas.
  2. Replies
    6$$
    Views
    844

    I have read that and figured they were not...

    I have read that and figured they were not needed, but for some reason I need reassurance. Thanks.
  3. Replies
    6$$
    Views
    844

    Yes outdoors.

    Yes outdoors.
  4. Replies
    14$$
    Views
    1,359

    Roto hammer with rod bit also.

    Roto hammer with rod bit also.
  5. Replies
    6$$
    Views
    844

    Coduit Seals emerging from duct bank

    Need some help here. We have a duct bank running from an unclassified area to classified. (Class1 Div 2). Entry into duct bank is via cable tray on both ends. Do we need seals at both ends of run...
  6. Replies
    5$$
    Views
    1,591

    We usually use a corn clamp and bond with a bond...

    We usually use a corn clamp and bond with a bond bushing. The listed tray clamps are very expensive.
  7. Replies
    21$$
    Views
    4,454

    You could excavate the bases, spin them as...

    You could excavate the bases, spin them as needed, reset and tamp around them. You will need a crane and excavator. It would be like setting a precast base.
  8. Thread: Pole light bases

    by DAWGS
    Replies
    0$$
    Views
    407

    Pole light bases

    Does anyone have a good labor unit for pole bases? I'm looking for a labor unit to include the following.

    Dig hole
    Set sauna tube
    Build rebar cage
    Install ground rod
    Install PVC stub outs...
  9. Replies
    6$$
    Views
    1,053

    Its running on 277V. We had an electrician hook...

    Its running on 277V. We had an electrician hook up to the wrong lead and fried it. There were 6 of them.
  10. Replies
    6$$
    Views
    1,053

    A regular em light is 6V output. These fixtures...

    A regular em light is 6V output. These fixtures are $250 each.
  11. Replies
    6$$
    Views
    1,053

    Looking for transformer

    120/277VAC input 14VDC output 1.35Amps. Came out of a Lithonia EM light.
  12. Replies
    15$$
    Views
    2,513

    By your post it sounds like you are dealing with...

    By your post it sounds like you are dealing with a bunch of whiners and complainers. Why would they not want to learn CPR? Sounds like they dont care to comply with any of the changes being made and...
  13. Thread: Fuses required?

    by DAWGS
    Replies
    4$$
    Views
    827

    They need to originate from fuses or a breaker...

    They need to originate from fuses or a breaker just like any branch circuit.
  14. Replies
    13$$
    Views
    1,469

    Next job let them build the rack and you use...

    Next job let them build the rack and you use there supports.:)
  15. Thread: T8 failed search

    by DAWGS
    Replies
    16$$
    Views
    1,800

    I would think you would be safe with that labor...

    I would think you would be safe with that labor unit. That many fixtures you can usually come up with time saving methods.
  16. Thread: Draw schedule?

    by DAWGS
    Replies
    36$$
    Views
    4,892

    If your under aGC it will probably be AIA billing.

    If your under aGC it will probably be AIA billing.
  17. Replies
    4$$
    Views
    1,031

    It cant be higher than 6' 7", isnt that what you...

    It cant be higher than 6' 7", isnt that what you mean. And yes it would need to meet those requirements.
  18. Thread: visioninfosoft

    by DAWGS
    Replies
    8$$
    Views
    764

    We use it. Great tech support when I need it...

    We use it. Great tech support when I need it also. I also took the class to learn the program, it was well worth the few hundred bucks for the class with Brian. You actually estimate a complete...
  19. Thread: Pendant Drops

    by DAWGS
    Replies
    3$$
    Views
    653

    Also we have to install these with a drop ceiling...

    Also we have to install these with a drop ceiling overhead. There is 18 drops. I was planning on dropping allthread and spannig strut across room just above grid to mount boxes on for hanging...
  20. Thread: Pendant Drops

    by DAWGS
    Replies
    3$$
    Views
    653

    Pendant Drops

    Can a light duty diecast bell box be used for pendant drops? Also does the box it hangs from also need a threaded hub?
  21. Thread: Card Access

    by DAWGS
    Replies
    51$$
    Views
    3,159

    Yup, same thing, DCJS "Department of Criminal...

    Yup, same thing, DCJS "Department of Criminal Justice Services". Back ground checks, fingerprinting, a compliance agent. You have to take a class. Most people dont realize that you actually need this...
  22. Thread: Card Access

    by DAWGS
    Replies
    51$$
    Views
    3,159

    Don't you also have to be DCJS licensed.

    Don't you also have to be DCJS licensed.
  23. Replies
    3$$
    Views
    544

    Thanks, I had just found it also. In my head I...

    Thanks, I had just found it also. In my head I was kind of remembering the exception and was a little confused.
  24. Replies
    3$$
    Views
    544

    Disconnect for Chiller

    I am installing power for a 300 ton chiller. The units MCA is 600A, the max OCP is 700A. My question is the disconnect, do I need a 600A disco or an 800A? I am thinking 800A as it would need to be...
  25. Thread: Economy

    by DAWGS
    Replies
    33$$
    Views
    2,289

    Poll: Hampton Roads, mostly industrial.

    Hampton Roads, mostly industrial.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4