Search:

Type: Posts; User: infinity

Page 1 of 8 1 2 3 4

Search: Search took 0.19 seconds.

  1. Thread: Full Size G

    by infinity
    Replies
    20$$
    Views
    360

    True, but the circuit conductors are the total of...

    True, but the circuit conductors are the total of all of the sets not just the size of the conductors in each raceway. In Jumpers example back in Post #2 for a 2500 amp OCPD you would have a 350...
  2. Replies
    16$$
    Views
    500

    A) Pigtail

    A) Pigtail
  3. Thread: Seal Fittings

    by infinity
    Replies
    11$$
    Views
    205

    Unless you have a hazardous location forget about...

    Unless you have a hazardous location forget about the sealing fittings. Sounds like typical boiler plate crap.
  4. Replies
    14$$
    Views
    332

    Are you just asking about dropping in the...

    Are you just asking about dropping in the fixtures or actually running the wiring first then installing them? If it's just the fixtures I don't see a 50-75% difference.
  5. Replies
    14$$
    Views
    332

    Up and down also lateral movement on the lift. ...

    Up and down also lateral movement on the lift. One the ground two men working on ladders is easy, on a 25' ceiling it may require two lifts, not as easy.
  6. Thread: Seal Fittings

    by infinity
    Replies
    11$$
    Views
    205

    312.2

    312.2
  7. Thread: Full Size G

    by infinity
    Replies
    20$$
    Views
    360

    Jumper gave you the code reference. The EGC in...

    Jumper gave you the code reference. The EGC in each parallel raceway is sized according to the OCPD ahead of the feeder. See post #2.
  8. Thread: Seal Fittings

    by infinity
    Replies
    11$$
    Views
    205

    Is this a hazardous location? Otherwise what is...

    Is this a hazardous location? Otherwise what is a seal fitting?
  9. The NEC will not tell you that you do not have to...

    The NEC will not tell you that you do not have to do it. This is about as close as you will get. IMO almost no piece of metal is likely to become energized.
  10. There needs to be a EGC run with the branch...

    There needs to be a EGC run with the branch circuit to each motor. I see no code reason to install the jumper you've mentioned.
  11. Thread: Full Size G

    by infinity
    Replies
    20$$
    Views
    360

    As Derek stated in parallel conductors also in...

    As Derek stated in parallel conductors also in engineering mistakes or the absolute desire to waste someones money. I did see a spec once where they wanted the EGC two sizes larger than the circuit...
  12. Welcome to the Forum. :) Short answer is no.

    Welcome to the Forum. :)

    Short answer is no.
  13. Replies
    11$$
    Views
    264

    Yes that is the minimum based on the...

    Yes that is the minimum based on the manufacturer's calculation which includes 125% of the largest motor load (typically the compressor) and as Texie pointed out you need to check the wiring method,...
  14. Replies
    22$$
    Views
    830

    Those exceptions were removed from the NEC in...

    Those exceptions were removed from the NEC in 2008. :)
  15. Thread: Placard

    by infinity
    Replies
    3$$
    Views
    292

    When I needed a sign for a generator inlet I went...

    When I needed a sign for a generator inlet I went to a local sign shop. One time custom signs aren't cheap due to the setup. I think that I paid $30 for this one.

    19356
  16. Replies
    81$$
    Views
    1,464

    Poll: I don't follow how this is applicable. Back to...

    I don't follow how this is applicable. Back to my earlier question, would you agree that if the area represented by the cabinet were a doorway then you would need a receptacle within 6' from the...
  17. Replies
    81$$
    Views
    1,464

    Poll: Where does it state that?

    Where does it state that?
  18. Replies
    81$$
    Views
    1,464

    Poll: So would you agree that if the area represented...

    So would you agree that if the area represented by the cabinet were a doorway then you would need a receptacle within 6' from the edges to both the right and the left?

    I agree with you in...
  19. Replies
    81$$
    Views
    1,464

    Poll: OK we can agree to disagree. :) The wording...

    OK we can agree to disagree. :)

    The wording is clear, once the wall line is broken you need to start over with the 6' spacing.
  20. Replies
    81$$
    Views
    1,464

    Poll: What Charlie is saying is that there are no...

    What Charlie is saying is that there are no receptacles required for the area occupied by the cabinet and that has nothing to do with the receptacles to the left and right of the cabinet. You still...
  21. Replies
    71$$
    Views
    2,236

    True, but I'm guessing that's not the reason why...

    True, but I'm guessing that's not the reason why it's 10' with one coupling. :D
  22. Replies
    71$$
    Views
    2,236

    Yup pretty dumb IMO.

    Yup pretty dumb IMO.
  23. Replies
    22$$
    Views
    830

    Here in NJ a single receptacle is permitted in...

    Here in NJ a single receptacle is permitted in lieu of a GFCI .
  24. Replies
    22$$
    Views
    830

    I'm pretty sure that those heaters will not fire...

    I'm pretty sure that those heaters will not fire if the unit is de-energized.
  25. Replies
    81$$
    Views
    1,464

    Poll: I agree too that you can install a receptacle in...

    I agree too that you can install a receptacle in either location if you so desire it's just not required.

    Welcome Back Larry. 8-)
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4