Search:

Type: Posts; User: Little Bill

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    15$$
    Views
    222

    It appears you are correct. If you enlarge the...

    It appears you are correct. If you enlarge the pic you will see a label (sticker) that has been added. Someone wrote on it "inside panel) with an arrow pointing to that top right breaker, which is...
  2. Replies
    15$$
    Views
    222

    That doesn't look like a split bus. Did you take...

    That doesn't look like a split bus. Did you take the cover off?
    As it is, the panel is legal because there isn't more than "6 throws of the hand" to turn all the breakers off.
  3. Since there is no "how to" question, I'll allow...

    Since there is no "how to" question, I'll allow this.
  4. Replies
    62$$
    Views
    2,224

    Takes a little focusing but it's the screw hole...

    Takes a little focusing but it's the screw hole of the box that is broken. It doesn't show the whole box.
  5. Replies
    62$$
    Views
    2,224

    From the product description listed in the link....

    From the product description listed in the link.

    Product description
  6. Replies
    4$$
    Views
    318

    I've installed them. You said new fixtures, the...

    I've installed them. You said new fixtures, the fixtures come with a disconnect in them.
  7. Thread: Beats me

    by Little Bill
    Replies
    9$$
    Views
    446

    You may know the difference between line and load...

    You may know the difference between line and load but if there are feeder wires to another receptacle, do you know which was line and which was load?

    Take the wires off the GFCI (with breaker off)...
  8. Replies
    13$$
    Views
    467

    I think neither of you need to take "Action" and...

    I think neither of you need to take "Action" and "Jumper to any conclusions!:D
  9. Replies
    7$$
    Views
    398

    Obviously you can, the pic clearly shows that!:)

    Obviously you can, the pic clearly shows that!:)
  10. Replies
    11$$
    Views
    420

    It didn't come out right but I was responding to...

    It didn't come out right but I was responding to the poster that said you loose the grounding or it would be compromised. I was trying to say if you had a wire EGC the grounding is not compromised.
  11. Replies
    11$$
    Views
    420

    You wouldn't have to bond the EMT if there is a...

    You wouldn't have to bond the EMT if there is a wire EGC in it.
  12. Thread: Hot Tub

    by Little Bill
    Replies
    9$$
    Views
    322

    I'm pretty sure that tubs that will run on either...

    I'm pretty sure that tubs that will run on either 120V or 240V have a warning about making sure it's correctly wired for the desired voltage. It also warns of what happens if it is set for 120V and...
  13. Well if you can find that in the code I'll agree...

    Well if you can find that in the code I'll agree with you. The intent might have been to include sheds but the wording doesn't back that up.
  14. I think the code is silent on sheds unless it...

    I think the code is silent on sheds unless it could be considered a garage.
    Better question is why would you not want a light being that there are already receptacles there?
  15. Replies
    8$$
    Views
    391

    Well you left that part out in your OP!;) You...

    Well you left that part out in your OP!;)
    You definitely have problems with one of the hot legs then.
    You could use a small load such as a "pigtail" socket and light bulb and put it across from...
  16. Replies
    8$$
    Views
    391

    Sounds like you have lost the neutral (grounded...

    Sounds like you have lost the neutral (grounded conductor) and maybe a loose connection on one of the hot legs as well. If you check the voltage with either a "Wiggy" or "Lo-Z" meter it probably...
  17. Replies
    32$$
    Views
    1,042

    Hmmm, post #12 must have been invisible.;)

    Hmmm, post #12 must have been invisible.;)
  18. Replies
    32$$
    Views
    1,042

    Make sure you don't have "line" & "load"...

    Make sure you don't have "line" & "load" reversed. If they are reversed the receptacle will not set. Other than that, if you have power present, then the GFCI is bad, try a new one.

    Not sure what...
  19. Replies
    1$$
    Views
    167

    Duplicate Please only start one thread for the...

    Duplicate

    Please only start one thread for the same subject.
  20. Replies
    1$$
    Views
    190

    I am closing this thread, in accordance with the ...

    I am closing this thread, in accordance with the Forum rules. This Forum is intended to assist professional electricians, inspectors, engineers, and other members of the electrical industry in ...
  21. Every POCO is different. Even though I'm in Tn I...

    Every POCO is different. Even though I'm in Tn I couldn't tell you what your POCO requires. But here, we can change a panel without changing the meter base and mast unless it is damaged or degraded...
  22. Replies
    38$$
    Views
    831

    I used an Insteon switch on an outdoor patio...

    I used an Insteon switch on an outdoor patio lighting project. The HO had an existing x-10 system and I just programmed the switch and used their existing remote. It might not have been 100 yds but...
  23. I was "poking" at you for this...

    I was "poking" at you for this...
  24. Replies
    11$$
    Views
    757

    I would have either toned it out or removed the...

    I would have either toned it out or removed the white wire to see what quit working. It was mentioned that disconnecting the red didn't cause anything to stop working so moving to the white would...
  25. Are you are you sure?:p

    Are you are you sure?:p
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4