Search:

Type: Posts; User: macmikeman

Page 1 of 8 1 2 3 4

Search: Search took 1.53 seconds.

  1. I feel like I have suffered damages from just...

    I feel like I have suffered damages from just reading all this. No excuse Eaton. All your profits for the last ten yrs should be yanked away from all the headaches you have caused electricians in...
  2. Thread: Am I Crazy?

    by macmikeman
    Replies
    42$$
    Views
    729

    Take your golf clubs out and wrap them around a...

    Take your golf clubs out and wrap them around a tree trunk. You won't be needing them any more is why.
  3. Replies
    24$$
    Views
    828

    I've seen a few fiberglass ones over the years. ...

    I've seen a few fiberglass ones over the years. Normally when we run pvc laterals to a pole we run up the first 8' of the pole and use 2 hole straps to secure to the wood, but on those fiberglass...
  4. Replies
    23$$
    Views
    979

    I wanna have a good look at the company owner's...

    I wanna have a good look at the company owner's wife before I decide if it is cash or gifts.
  5. Thank you Robert , I thought so. Anything on...

    Thank you Robert , I thought so. Anything on each laddder rung before the last resistance was hot as I was taught and after that came the neutral side bus hookups. I understand the .5 volt dc ...
  6. A little help with a discussion elsewhere about plc switching neutrals

    At another Q+A electrical place the question about a plc that switches the neutrals instead of the hot side of the circuits is going on.
    I'm retired from grabbing a code book. We know you cant do...
  7. Thread: PICTURES

    by macmikeman
    Replies
    27$$
    Views
    1,131

    Very nice prof. job. This years winner of the...

    Very nice prof. job. This years winner of the macmikeman seal of approval. Even Pipe Nick down thar in Orlando would be awed by that job.
  8. Replies
    44$$
    Views
    1,518

    Are there any electricians on the CMP'S anymore? ...

    Are there any electricians on the CMP'S anymore? Where I am at we are still on the 08. After reading this thread all the way thru and with no real clue as to whether there are or not, (I know...
  9. Replies
    57$$
    Views
    1,561

    Bravo, I was thinking the same thing, but there...

    Bravo, I was thinking the same thing, but there is no thank's button to hit so I will use this- 8-)
  10. Replies
    37$$
    Views
    849

    If it is in a wet location, even the threaded ko...

    If it is in a wet location, even the threaded ko seals that makers of wp bell boxes state that additional sealant must be used to seal around the ko plugs. Up here on Planet Macmikeman everyone...
  11. Apparently work itself is life threatening when...

    Apparently work itself is life threatening when one reflects on that report. Probably a good time to reconsider the possibility of just becoming a beach bum and spend your life laying about in the...
  12. Replies
    20$$
    Views
    1,737

    Parapets like the one in the picture I like to...

    Parapets like the one in the picture I like to mirror the unistrut on the backside as well as the one on the front side and thru bolt using threaded rods drilled thru the brick joints. Maybe even use...
  13. Replies
    34$$
    Views
    1,313

    What I find 9 times out of 10 is a plumbers vent...

    What I find 9 times out of 10 is a plumbers vent pipe running straight up thru where the light fixture is clearly showing on the prints.
    Lots of times they are quite large pipes and are drilled very...
  14. Replies
    37$$
    Views
    849

    Of course not. That is as crazy as using ''old...

    Of course not. That is as crazy as using ''old work boxes'' in new construction.............. Why would you use anything else besides RMC in the first place. We all know it is the...
  15. Replies
    34$$
    Views
    1,313

    That house should have been wired with rigid...

    That house should have been wired with rigid galvanized conduit in the first place and that would have ensured that the box was mounted rigidly enough to support the $16 dollar light fixtures that...
  16. Replies
    4$$
    Views
    407

    For a long time now, I have been of the opinion...

    For a long time now, I have been of the opinion that whenever I read Forensic articles from forensic engineers in ECM Magazine that it is time to slip on the rubber boots . Just drive another...
  17. Replies
    46$$
    Views
    1,318

    We here in the land of Aloha have some inspectors...

    We here in the land of Aloha have some inspectors demanding the 3 pole switch to be installed to open all three legs of the control cable between units. That is a thirty dollar device around these...
  18. Replies
    46$$
    Views
    1,318

    As I recall that was a ''It's time for your...

    As I recall that was a ''It's time for your mactip of the day!'' #37 I believe, first published many many years prior to now..........



    However it was bested by '' It's time for your mactip of...
  19. Replies
    29$$
    Views
    790

    Here it is- was really easy to locate - I use...

    Here it is- was really easy to locate - I use search engines, they are a new fangled thing you can find on the internets. ...
  20. Replies
    29$$
    Views
    790

    Is Siemens still pushing that expensive afci...

    Is Siemens still pushing that expensive afci fault locator tool that never identifies the breaker itself as the problem? If you do go into this business, that would be a worthwhile tool to keep...
  21. Replies
    11$$
    Views
    657

    Exclude trenching, excavation, backfill, and...

    Exclude trenching, excavation, backfill, and concrete sawcutting and removal from your bids. Or do it all time and material and if you cut some lines just add the repair costs into the invoice,...
  22. Just click your username at the top right of the...

    Just click your username at the top right of the screen. It displays a list view of your threads you were last on. Mine shows that I replied to a thread about Asian Massage. Well it is...
  23. Replies
    18$$
    Views
    1,131

    I have had success with using a teeny grinding...

    I have had success with using a teeny grinding wheel and a dremel tool , but it didn't seem to last for very long once I got it sharp again.
  24. Replies
    12$$
    Views
    556

    You should follow the rules for patient care...

    You should follow the rules for patient care areas. Asian massage parlors have shocking things that happen in there. Shocking.
  25. This is a perfect unlooked feature that just may...

    This is a perfect unlooked feature that just may help somebody win the '' I got me the most code changes in so I am the obvious best electrician ever contest''. Better hurry before somebody else...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4