Search:

Type: Posts; User: ptonsparky

Page 1 of 8 1 2 3 4

Search: Search took 0.66 seconds; generated 26 minute(s) ago.

  1. They were offered by the utilities around here...

    They were offered by the utilities around here for a while but havent seen or heard of them for several years.
  2. ...I could not buy supper for two at The Cellar.

    ...I could not buy supper for two at The Cellar.
  3. Replies
    26$$
    Views
    549

    Power off at the Main. Shut off all CBs. Gas or...

    Power off at the Main. Shut off all CBs.
    Gas or electric range and dryer?
    Are they 3 or 4 wire if electric? If 4, check for proper connection at the appliance. If 3, unplug them.

    Check...
  4. Replies
    14$$
    Views
    491

    One truck heater per GFCI and depending on...

    One truck heater per GFCI and depending on wattage, one per circuit.
  5. Replies
    14$$
    Views
    491

    What do you think the 120v would be doing to it...

    What do you think the 120v would be doing to it when the GFCI is removed?

    "Dead" or maybe highly unlikely "fried electronics". Decisions, decisions.
    If your checking the block heater, check...
  6. Replies
    14$$
    Views
    491

    Get your megger out and check each truck heater. ...

    Get your megger out and check each truck heater. Red tag the units that fail.
    . Check the extension cords.
    Make sure proper covers are on the devices after you upgrade to the WRs as suggested....
  7. Replies
    2$$
    Views
    135

    GFP vs 6 Main

    Customer is planning on adding some refrigeration units. The changes will require an upgrade from the existing 800 MDP with 6 mains, to a 1200. 480/277.

    The best layout for me is to go back in...
  8. Replies
    27$$
    Views
    789

    The trick will be to release the "starter"of the...

    The trick will be to release the "starter"of the gen when it starts. . Looks you dont have a cold weather problem so that should help. Do you have to choke it?
  9. Replies
    16$$
    Views
    586

    There is a story about the customer not wanting...

    There is a story about the customer not wanting to pay his bill because the mechanic just wacked it with a hammer. Yup, the machanic said, $10 for diagnosis, and $50 for knowing exactly where to hit...
  10. Replies
    15$$
    Views
    568

    To bad they dont cal the BIL back when things...

    To bad they dont cal the BIL back when things quit working.
  11. Replies
    15$$
    Views
    568

    They make options for cu to al connections. Are...

    They make options for cu to al connections. Are you wanting options how to do it properly or how it was most likely done?
  12. Replies
    29$$
    Views
    996

    Not sure why they put fans on ag motors. A good...

    Not sure why they put fans on ag motors. A good share of them have the fan cover gone and or the blades. They last for years when used sporadically in grain handling. Amazed at how much abuse...
  13. PTD25-20-0100WCH ...

    PTD25-20-0100WCH

    PRESS XMTR 0 TO 100inWC 4-20mA 1/4in MNPT M12 PLUG

    I think I could even do it.
  14. The village my shop is in recently put in a VFD...

    The village my shop is in recently put in a VFD on one of their pumps to maintain the level in the water tower. It has a pressure transducer but all it really does is attempt to maintain a certain...
  15. It doesn't explain why she didn't have a fire to...

    It doesn't explain why she didn't have a fire to go along with it. Lucky woman, IMO.
  16. Baseboard heat?

    Baseboard heat?
  17. Good solution.

    Good solution.
  18. Replies
    31$$
    Views
    829

    Last old cranes I was around used wound rotors...

    Last old cranes I was around used wound rotors and banks of resistors for speed control. Grounding was not high on the list. Thinking none, as Jraef described. This was a 40 ton overhead. We had...
  19. Many fixtures have words to the affect that 90...

    Many fixtures have words to the affect that 90 deg C wiring must be use for supply conductors.

    That said, the customer may opt to do nothing. No money sometimes means No money.
  20. Replies
    31$$
    Views
    829

    You read 480v to ground... L1-G, L2-G, L3-G after...

    You read 480v to ground... L1-G, L2-G, L3-G after the motor has started to run but 277 each phase to ground prior to it running?
  21. Not if you are a guy that is only interested in...

    Not if you are a guy that is only interested in selling a water pump with control.
  22. Replies
    31$$
    Views
    829

    Now describe your methods of measurements. From...

    Now describe your methods of measurements. From Where to Where.
  23. Given your knowledge and experience level vs...

    Given your knowledge and experience level vs mine, I am a bit hesitant, but Yes, unless some other mechanical means was employed which would negate the reason for the drive.
  24. Replies
    4$$
    Views
    316

    Grounding Electrode Conductors - Yes they can be...

    Grounding Electrode Conductors - Yes they can be "oversized" if they do not fit into the lugs you are using or they break the budget, otherwise have at it. IMO.
  25. All the ones I have seen, yes.

    All the ones I have seen, yes.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4