Search:

Type: Posts; User: DAWGS

Page 1 of 8 1 2 3 4

Search: Search took 0.25 seconds.

  1. Replies
    6$$
    Views
    1,107

    Thanks for the replies fellas.

    Thanks for the replies fellas.
  2. Replies
    6$$
    Views
    1,107

    I have read that and figured they were not...

    I have read that and figured they were not needed, but for some reason I need reassurance. Thanks.
  3. Replies
    6$$
    Views
    1,107

    Yes outdoors.

    Yes outdoors.
  4. Replies
    14$$
    Views
    1,850

    Roto hammer with rod bit also.

    Roto hammer with rod bit also.
  5. Replies
    6$$
    Views
    1,107

    Coduit Seals emerging from duct bank

    Need some help here. We have a duct bank running from an unclassified area to classified. (Class1 Div 2). Entry into duct bank is via cable tray on both ends. Do we need seals at both ends of run...
  6. Replies
    5$$
    Views
    1,856

    We usually use a corn clamp and bond with a bond...

    We usually use a corn clamp and bond with a bond bushing. The listed tray clamps are very expensive.
  7. Replies
    21$$
    Views
    5,057

    You could excavate the bases, spin them as...

    You could excavate the bases, spin them as needed, reset and tamp around them. You will need a crane and excavator. It would be like setting a precast base.
  8. Thread: Pole light bases

    by DAWGS
    Replies
    0$$
    Views
    459

    Pole light bases

    Does anyone have a good labor unit for pole bases? I'm looking for a labor unit to include the following.

    Dig hole
    Set sauna tube
    Build rebar cage
    Install ground rod
    Install PVC stub outs...
  9. Replies
    6$$
    Views
    1,166

    Its running on 277V. We had an electrician hook...

    Its running on 277V. We had an electrician hook up to the wrong lead and fried it. There were 6 of them.
  10. Replies
    6$$
    Views
    1,166

    A regular em light is 6V output. These fixtures...

    A regular em light is 6V output. These fixtures are $250 each.
  11. Replies
    6$$
    Views
    1,166

    Looking for transformer

    120/277VAC input 14VDC output 1.35Amps. Came out of a Lithonia EM light.
  12. Replies
    15$$
    Views
    2,754

    By your post it sounds like you are dealing with...

    By your post it sounds like you are dealing with a bunch of whiners and complainers. Why would they not want to learn CPR? Sounds like they dont care to comply with any of the changes being made and...
  13. Thread: Fuses required?

    by DAWGS
    Replies
    4$$
    Views
    902

    They need to originate from fuses or a breaker...

    They need to originate from fuses or a breaker just like any branch circuit.
  14. Replies
    13$$
    Views
    1,620

    Next job let them build the rack and you use...

    Next job let them build the rack and you use there supports.:)
  15. Thread: T8 failed search

    by DAWGS
    Replies
    16$$
    Views
    2,089

    I would think you would be safe with that labor...

    I would think you would be safe with that labor unit. That many fixtures you can usually come up with time saving methods.
  16. Thread: Draw schedule?

    by DAWGS
    Replies
    36$$
    Views
    5,541

    If your under aGC it will probably be AIA billing.

    If your under aGC it will probably be AIA billing.
  17. Replies
    4$$
    Views
    1,177

    It cant be higher than 6' 7", isnt that what you...

    It cant be higher than 6' 7", isnt that what you mean. And yes it would need to meet those requirements.
  18. Thread: visioninfosoft

    by DAWGS
    Replies
    8$$
    Views
    819

    We use it. Great tech support when I need it...

    We use it. Great tech support when I need it also. I also took the class to learn the program, it was well worth the few hundred bucks for the class with Brian. You actually estimate a complete...
  19. Thread: Pendant Drops

    by DAWGS
    Replies
    3$$
    Views
    717

    Also we have to install these with a drop ceiling...

    Also we have to install these with a drop ceiling overhead. There is 18 drops. I was planning on dropping allthread and spannig strut across room just above grid to mount boxes on for hanging...
  20. Thread: Pendant Drops

    by DAWGS
    Replies
    3$$
    Views
    717

    Pendant Drops

    Can a light duty diecast bell box be used for pendant drops? Also does the box it hangs from also need a threaded hub?
  21. Thread: Card Access

    by DAWGS
    Replies
    51$$
    Views
    3,554

    Yup, same thing, DCJS "Department of Criminal...

    Yup, same thing, DCJS "Department of Criminal Justice Services". Back ground checks, fingerprinting, a compliance agent. You have to take a class. Most people dont realize that you actually need this...
  22. Thread: Card Access

    by DAWGS
    Replies
    51$$
    Views
    3,554

    Don't you also have to be DCJS licensed.

    Don't you also have to be DCJS licensed.
  23. Replies
    3$$
    Views
    594

    Thanks, I had just found it also. In my head I...

    Thanks, I had just found it also. In my head I was kind of remembering the exception and was a little confused.
  24. Replies
    3$$
    Views
    594

    Disconnect for Chiller

    I am installing power for a 300 ton chiller. The units MCA is 600A, the max OCP is 700A. My question is the disconnect, do I need a 600A disco or an 800A? I am thinking 800A as it would need to be...
  25. Thread: Economy

    by DAWGS
    Replies
    33$$
    Views
    2,478

    Poll: Hampton Roads, mostly industrial.

    Hampton Roads, mostly industrial.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4