Search:

Type: Posts; User: norcal

Page 1 of 8 1 2 3 4

Search: Search took 0.64 seconds.

  1. Replies
    7$$
    Views
    337

    Go to a PG&E office (Not a bill pay location) &...

    Go to a PG&E office (Not a bill pay location) & get a copy of their greenbook or try this: http://www.pge.com/mybusiness/customerservice/otherrequests/newconstruction/greenbook/servicerequirements/
  2. Why not use a transformer?

    Why not use a transformer?
  3. The FPE issues were with the residential Stablok...

    The FPE issues were with the residential Stablok loadcenters, from what I understand the rest of their product line was fine.
  4. Replies
    6$$
    Views
    529

    This is good advice, no sense in putting your...

    This is good advice, no sense in putting your license at risk.
  5. Replies
    5$$
    Views
    157

    Isn't all modern circuit breakers "trip free" ? ...

    Isn't all modern circuit breakers "trip free" ? So holding the breaker handle should not affect tripping in a fault/ overload situation.
  6. Thread: T-12 Ballasts

    by norcal
    Replies
    10$$
    Views
    660

    Use a 4-lamp T8 ballast & T8 lamps, mixing T8...

    Use a 4-lamp T8 ballast & T8 lamps, mixing T8 lamps with T12 ballasts is a bad practice that will lead to callbacks.
  7. Thread: 3 phase panel

    by norcal
    Replies
    4$$
    Views
    318

    Is any equipment for use over 240 volts cheap? ...

    Is any equipment for use over 240 volts cheap? Should be able to find a 24 space panel pretty easy, but that is not the question.
  8. Replies
    4$$
    Views
    417

    Here is the Reloc website. ...

    Here is the Reloc website. http://www.relocwiring.com/
  9. Replies
    26$$
    Views
    939

    Bought a Klein when I could not find my Roto...

    Bought a Klein when I could not find my Roto Split, I don't like it either but did find the Roto split. :D
  10. It is my opinion, but I could not bring myself to...

    It is my opinion, but I could not bring myself to add ungrounded metallic Wiremold extensions to a system, which is why it was prefaced w/"IMHO".
  11. IMHO, it would need to be a non-metallic...

    IMHO, it would need to be a non-metallic extension.
  12. Replies
    35$$
    Views
    1,605

    But one does have to use a lot of "Industrial...

    But one does have to use a lot of "Industrial English" when one comes across people who did use 10AWG then to make matters worse, shallow boxes & short wire. :happysad:
  13. Replies
    14$$
    Views
    812

    Challenger was Zinsco in a former life, but most...

    Challenger was Zinsco in a former life, but most of Zinsco's issues were with plug-in breakers & their problematic aluminum bus. As much as I think that Zinsco products & their successors/ knockoffs...
  14. Replies
    13$$
    Views
    548

    That one takes care of the ground up/down debate...

    That one takes care of the ground up/down debate if they have those discussions.
  15. Replies
    9$$
    Views
    681

    When a lot of garages were unfinished around here...

    When a lot of garages were unfinished around here the way it was handled was to run the wiring overhead & then drop it down to the device, then it was drywalled covering only that stud bay containing...
  16. Replies
    9$$
    Views
    681

    MC is subject to the same requirements for...

    MC is subject to the same requirements for protection from physical damage as NM cable. See 330.12(1).
  17. Replies
    14$$
    Views
    719

    Crouse-Hinds used to list competitive makes of...

    Crouse-Hinds used to list competitive makes of breakers allowed in their loadcenters, but since Siemens got them never paid attention if that is still the case but I really doubt it. :p
  18. Replies
    34$$
    Views
    1,207

    Yikes! A product looking for a purpose.

    Yikes! A product looking for a purpose.
  19. Replies
    34$$
    Views
    1,207

    Just to satisfy my curiosity how much are they...

    Just to satisfy my curiosity how much are they going for? No, not looking to get any. :lol:
  20. Replies
    14$$
    Views
    587

    And not "110V".

    And not "110V".
  21. Replies
    4$$
    Views
    556

    In that application neither cable is suitable for...

    In that application neither cable is suitable for 100A & 4/3 NM is only suitable for 70A as it has to be sized from the 60 degree column of table 310.16.

    Edit #2, I think that there are a few...
  22. Replies
    49$$
    Views
    2,580

    Now that this tread has run for a bit, what was...

    Now that this tread has run for a bit, what was the solution agreed by the AHJ & the OP? Inquiring minds want to know. :lol:
  23. Thread: Load Centers

    by norcal
    Replies
    13$$
    Views
    565

    But the QO is a cheesy plastic interior.

    But the QO is a cheesy plastic interior.
  24. Thread: Load Centers

    by norcal
    Replies
    13$$
    Views
    565

    I prefer Eaton/Cutler-Hammer type CH loadcenters...

    I prefer Eaton/Cutler-Hammer type CH loadcenters , copper bus & I see that Eaton is copying the SQ D Visi-TripĀ® indicator too, Siemens offers copper bussed panels too.
  25. Replies
    18$$
    Views
    799

    Main is a Zinsco style, which means it's...

    Main is a Zinsco style, which means it's Challenger, Bryant/Westinghouse, or General Switch, GS is my guess.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4