Search:

Type: Posts; User: fifty60

Page 1 of 8 1 2 3 4

Search: Search took 0.37 seconds.

  1. Replies
    9$$
    Views
    140

    Insulation on MTW or THHN/THWN Wires

    If my wire is rated for 600V, would this be considered its line to neutral rating? Or would it be the line to line rating?
  2. Replies
    6$$
    Views
    147

    Sizing Transformer For Solenoids

    I have several 115V solenoids that I need to supply from a 460V source. I will use a general purpose transformer to step down the voltage to the solenoids. The solenoids have a 180A inrush, with a...
  3. Replies
    2$$
    Views
    200

    460V-480V

    460V-480V
  4. Replies
    1$$
    Views
    136

    Circuit Breaker Labels

    I make circuit breaker labels to affix to equipment before they are shipped to the customer. I have an odd piece of equipment here that has a refrigeration compressor and an air circulator fan. ...
  5. Replies
    2$$
    Views
    200

    Single Phase VS Three Phase Transformer

    I can recommend the selection of a single phase remote refrigeration compressor power pack, or a three phase version. The single phase has voltage requirement of 208-230V at an RLA of 6.3A and the...
  6. Replies
    20$$
    Views
    762

    If you new that you had to run 8/4 (3 current...

    If you new that you had to run 8/4 (3 current carrying plus one ground wire) AC, MC, or flex cable to a piece of equipment, white size cutout would you want to see?

    No cutout is not an option. I...
  7. Replies
    20$$
    Views
    762

    No, the equipment will be supplied without the...

    No, the equipment will be supplied without the power chord. The installer has the option of using a chord and plug, or making it permenantly connected to a disconnect. If it is permanently...
  8. Replies
    20$$
    Views
    762

    Can the fitting that connects the MC Cable to the...

    Can the fitting that connects the MC Cable to the equipment enclosure be considered strain relief? Does it actually provide any strain relief?
  9. Replies
    20$$
    Views
    762

    I have been researching conduit in general, and...

    I have been researching conduit in general, and have now familiarized myself with MC and Flex cables. I believe that due to the inherent vibration of the equipment, that this will be the most likely...
  10. Replies
    20$$
    Views
    762

    This type of strain relief is wall mountable...

    This type of strain relief is wall mountable right? And the NPT threaded fitting on the back would be used to attach a conduit to?

    11189
  11. Replies
    20$$
    Views
    762

    Right now I just have an opening on the top of...

    Right now I just have an opening on the top of the equipment. The GC who installs the equipment will be required to supply the strain relief for the power connection. If cable (SOOW for example) is...
  12. Replies
    20$$
    Views
    762

    This equipment does not want to run cable, it...

    This equipment does not want to run cable, it only wants the individual conductors. If it were cable, the solution would be to get a strain relief fitting. With the individual conductors, I would...
  13. Replies
    20$$
    Views
    762

    The distribution blocks are available immediately...

    The distribution blocks are available immediately after the conductors enter the equipment. The conductors are not "flying around" as I had originally though, they run less than a foot and land in...
  14. Replies
    1$$
    Views
    121

    Air Tight Thermocouple Jacks/Plugs

    I have used these Omega thermocouple jacks and plugs in the past. I am looking for something similar now, but they will need to be as close to air tight as possible. With these connectors, whenever...
  15. Replies
    20$$
    Views
    762

    The grommet protection at the power conductor...

    The grommet protection at the power conductor entry point is for abrasion protection only, and does not supply any strain relief. The power conductors then are ran open inside the equipment until...
  16. Replies
    20$$
    Views
    762

    Sorry, it is not 8/3 cable, but actually...

    Sorry, it is not 8/3 cable, but actually THHN/THHW wires outside of a jacket. The NEC table is actually 310.15(b)(16) (formerly 310.16) using the 2011 NEC.

    The sub panel is located on the front...
  17. Replies
    20$$
    Views
    762

    They are sized from table 310.15(b)15...so I...

    They are sized from table 310.15(b)15...so I THHW/THHN..
  18. Replies
    20$$
    Views
    762

    Do I Need Conduit?

    I have 8/3 cable that is carrying 208V and 35A. For most of the equipment I work with, this would be ran inside a 1 1/4" emt until it reaches the equipment sub panel. The equipment I am seeing now...
  19. Replies
    1$$
    Views
    167

    Transformer Question (450.3(B))

    I have a transformer that draws more than 9 amps on the primary. When I reference 450.3(B) to size the primary protection, when primary and secondary protection are present, I see that I can size...
  20. Replies
    1$$
    Views
    113

    Resolution using PT100 RTD

    I am trying to determine the resolution of my temperature controller. My sensor is a PT100 RTD. The temperature range for the controller using the RTD is -210 to 700. The ADC on my temperature...
  21. Replies
    2$$
    Views
    183

    EQUIPMENT GROUNDING CONDUCTOR

    I have equipment that is sometimes provided with a safety switch disconnect located on the equipment, and sometimes this disconnect is located external to the equipment.

    If the disconnect is...
  22. Replies
    15$$
    Views
    496

    Metric Sizes for EMT

    I have 1 1/4" EMT that I need to convert to the equivalent metric size. I am finding that 35mm is the equivalent metric size, but I did not know if that is an exact measurement or an approximation. ...
  23. Replies
    6$$
    Views
    207

    So my primary to secondary ratio is 575/230= 2.5....

    So my primary to secondary ratio is 575/230= 2.5. So if my load is drawing 6A, would I then make my contribution to the equipment fla 6/2.5 = 2.4A?
  24. Replies
    6$$
    Views
    207

    My question can be summed up as follows: I have...

    My question can be summed up as follows: I have a branch circuit inside of my equipment that consists of a 3KVA transformer. The 3KVA transformer has 2 motors across its secondary. Is it...
  25. Replies
    4$$
    Views
    217

    GoldDigger, the rated HP of the compressors will...

    GoldDigger, the rated HP of the compressors will decrease with the decrease in Voltage and frequency.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4