Search:

Type: Posts; User: JeffKiper

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Thread: C1D1GC

    by JeffKiper
    Replies
    5$$
    Views
    1,024

    Bob the entire area is C1D1. So the existing...

    Bob the entire area is C1D1. So the existing union. Would be replaced also.

    Thanks for your fast reply
  2. Thread: C1D1GC

    by JeffKiper
    Replies
    5$$
    Views
    1,024

    Bob I apologize for not responding. The...

    Bob I apologize for not responding.

    The customer has stated that they are going to change the extire conduit run to XP. There are 3 fittings in the conduit that are not XP. they intend to replace...
  3. Daramic???? Are you going to try to change the...

    Daramic????
    Are you going to try to change the extraction rooms classification
  4. Thread: C1D1GC

    by JeffKiper
    Replies
    5$$
    Views
    1,024

    C1D1GC

    Existing system the customer wants to change a field dwvice from IS to XP. The conduit is 1" GRC. A seal at the enclosure end of the conduit and standard fittings from there put to the end device. Im...
  5. Replies
    4$$
    Views
    1,429

    Too many trees to see the forest.

    A claw hammer and a brass hammer to drive the claws. Sometimes we overlook the simple options.

    Thabk you gentelmen have a great day.
  6. Replies
    4$$
    Views
    1,429

    Pin anchor removal

    I need to move a conduit in a C1D1D area. They used drive in pin anchors to attache to the floor. I can't use a grinder even an air powered they wont let me.
    Do you have any ideas how to remove the...
  7. Replies
    8$$
    Views
    1,463

    Bob I work for end users 99% of the time. I...

    Bob I work for end users 99% of the time.

    I learned that machine builders are usually very cost ...... (You can fill in the blank) I also proved to 1 guy that the added cost of AB hardware on an...
  8. Replies
    8$$
    Views
    1,463

    cpickett You hit it exactly. I have some...

    cpickett

    You hit it exactly. I have some experience with rigid. I'm a toolaholic so I'm tooled up to do just about anythingon 2" and down. 555, Chicago, 1 little pony, 1 regular pony, threaders,...
  9. Replies
    8$$
    Views
    1,463

    I have only seen a few software packages. From...

    I have only seen a few software packages. From what I saw they where for running lots of pipe.
    I dont kniw if there are any specifically for machine wiring. There's a lot of examples from...
  10. Replies
    8$$
    Views
    1,463

    Rookie estimating machine wiring

    I run a small 3 man industrial controls shop. I'm getting more and more request for turnkey controls upgrades. I can quote the controls side all day long and am happy with that. My problem is quoting...
  11. Replies
    1$$
    Views
    607

    C1D1 temperature switch requirement

    Guys I have been looking in 500 and can't find a requirement for temperature switches within motors located in a classified area.

    Historically I have always pulled the temp switches and field...
  12. Replies
    15$$
    Views
    2,345

    Louisville Ky

    Louisville Ky
  13. Replies
    15$$
    Views
    2,345

    Your right, it is usually do it now! I haven't...

    Your right, it is usually do it now!

    I haven't been very good a tracking time. I need to do a better job and start creating a history so I can pull pricing from.
  14. Replies
    15$$
    Views
    2,345

    Sometimes it is last minute ideas that they have...

    Sometimes it is last minute ideas that they have been thinking about.

    Several of them are safety issues that have resulted in accidents and they need a quick response. We don't design guarding...
  15. Replies
    15$$
    Views
    2,345

    Most of the time the machine is existing and we...

    Most of the time the machine is existing and we are adding safety devices to it. The motors and standard valves are existing. So we just have to add devices.

    On new jobs or big jobs I let the...
  16. Replies
    15$$
    Views
    2,345

    Controls geek running pipe.

    I am learning so put me in my place if this is not an acceptable question.

    Guys I own a 2 man industrial controls shop. We assemble UL508A panels, controls, programming, etc. We specialize in...
  17. Replies
    7$$
    Views
    1,064

    Posting from my phone so please excuse the...

    Posting from my phone so please excuse the sideways image. I can't figure out how to rotate when posting a pic from my phone.

    I added some LED roll lights and 2 door switches. They make life nice...
  18. Replies
    7$$
    Views
    1,064

    Cord reel for gangbox

    OK guys I'm setting up a new gangbox and want to make this thing user friendly. It is going to have lights in it. This is a large Knaack 112 with shelves. It will be setup for control guys so a lot...
  19. Replies
    0$$
    Views
    499

    Fitting gang box ideas

    I'm getting ready to put a gang box together just for fittings. We typically use RMC, sealtight, cord grips 3/4" and 1". We use 1/2" just at the device. I'm trying to make a list of fittings to stock...
  20. Replies
    23$$
    Views
    4,826

    I do a lot of machine controls in plants mainly. ...

    I do a lot of machine controls in plants mainly. If it is an outside or wet job I try to use fiberglass and/or plastic to keep corrosion ti a minimum.

    I don't know for sure but doesn't metallic...
  21. Replies
    23$$
    Views
    4,826

    I only use LFNC when doing water systems or...

    I only use LFNC when doing water systems or outside work.
  22. Replies
    23$$
    Views
    4,826

    Yea I hadn't thought about leaving the system...

    Yea I hadn't thought about leaving the system open to air and nasty oils floating around a plant. Good point. Thanks.
  23. Replies
    23$$
    Views
    4,826

    So you use a threaded coupling and a cord grip...

    So you use a threaded coupling and a cord grip bushing. We did a few that way. I don't use that anymore . I don't know why we jist don't.
  24. Replies
    23$$
    Views
    4,826

    Sorry I re-read my post and it was as clear as...

    Sorry I re-read my post and it was as clear as mud.

    What I was trying to say was the compression ring that threads inside the sealtite. The sealtite fitting is a 3 pc unit not includong the...
  25. Replies
    23$$
    Views
    4,826

    Guys thanks for the replies. I am just going to...

    Guys thanks for the replies. I am just going to stock 1/2" sealtite and fitting in the gang boxes.

    The only time we really use this is when wiring field devices like safey gate switches.
    ...
Results 1 to 25 of 29
Page 1 of 2 1 2