Search:

Type: Posts; User: cdslotz

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    7$$
    Views
    794

    why is there 120V running to these devices?

    why is there 120V running to these devices?
  2. Replies
    7$$
    Views
    496

    Yes....I think their intent was to have the new...

    Yes....I think their intent was to have the new switch/shunt control everything.
    Those elevator switches are not cheap (as you know)
  3. Replies
    38$$
    Views
    3,553

    I had an EC friend of mine in the 90's that did...

    I had an EC friend of mine in the 90's that did Wal Marts all over Texas and other states.
    He knew the exact cost, down to every nut/bolt/screw, for every floorplan that WalMart built.
    I was...
  4. Replies
    11$$
    Views
    3,083

    Your average rate is YOUR average rate. What...

    Your average rate is YOUR average rate.
    What will your average manloading be on the job? 8 men? 20 men?
  5. Replies
    30$$
    Views
    4,698

    I don't understand how hard it would be to find...

    I don't understand how hard it would be to find out the contractor of record on the permit.
  6. Replies
    30$$
    Views
    4,698

    99.9% chance that is the case. Find out who the...

    99.9% chance that is the case.
    Find out who the EC was and call him
  7. Thread: Means/Method

    by cdslotz
    Replies
    12$$
    Views
    1,814

    Imagine if the specs had that typo.....words have...

    Imagine if the specs had that typo.....words have meaning
  8. Thread: Means/Method

    by cdslotz
    Replies
    12$$
    Views
    1,814

    What?.....you just said in the OP that the spec...

    What?.....you just said in the OP that the spec required you to run EMT out of the panel....

    once again.......you contradict yourself in a matter of three posts
  9. Replies
    40$$
    Views
    5,235

    How do you think GC's limit their...

    How do you think GC's limit their liability?......subs
  10. Replies
    40$$
    Views
    5,235

    thank you....and that's the way I would have done...

    thank you....and that's the way I would have done it.

    Once I get the job...I would take those labor/material dollars and compare it to a rigger's quote. Anytime I can put the liability on someone...
  11. Replies
    40$$
    Views
    5,235

    Still no answer on how it was estimated....?

    Still no answer on how it was estimated....?
  12. Replies
    40$$
    Views
    5,235

    thank you Captain Obvious....lol

    thank you Captain Obvious....lol
  13. Replies
    40$$
    Views
    5,235

    How much labor do you have to hang these? How...

    How much labor do you have to hang these?
    How much did you include for lifts/rigging?
    How much did you include for supports for 550 lb units (welding, strut,etc) and were there structural details...
  14. Replies
    40$$
    Views
    5,235

    How was this work estimated?

    How was this work estimated?
  15. Replies
    40$$
    Views
    5,235

    I would absolutely do this ^^^ I would not want...

    I would absolutely do this ^^^
    I would not want any liability for damaging property or personnel.

    I must ask....how is something like this even in your scope of work? Are you the primary...
  16. Thread: MC Support

    by cdslotz
    Replies
    5$$
    Views
    1,232

    Looks like a city ordinance....waste of money?...

    Looks like a city ordinance....waste of money? Maybe

    Ye shall comply
  17. Replies
    11$$
    Views
    3,046

    Most out of town GC's come into town to build a...

    Most out of town GC's come into town to build a chain store/restaurant that they have built a hundred times. They know exactly how much the electrical should run. Your bid to them is the starting...
  18. Replies
    11$$
    Views
    3,046

    Bidding out of town GC's and Taco Bells is a race...

    Bidding out of town GC's and Taco Bells is a race to the bottom
  19. Replies
    44$$
    Views
    9,634

    It says ConEst on the document

    It says ConEst on the document
  20. Thread: Shaft Conduits

    by cdslotz
    Replies
    16$$
    Views
    2,216

    ....and your question is.....?

    ....and your question is.....?
  21. Replies
    8$$
    Views
    1,345

    All software has RMC, LB's, condulets, unions,...

    All software has RMC, LB's, condulets, unions, explosion proof boxes, all types of fittings, all types of wire, terminations, etc.......what more do you need?
  22. Replies
    19$$
    Views
    843

    Just think what a 277/480V MWBC in an office...

    Just think what a 277/480V MWBC in an office where you have a 3-pole CB. When you shut that off, or even worse, it trips, an entire floor of lighting can be killed
  23. Replies
    44$$
    Views
    9,634

    If it's like Texas, they use sub-crews...

    If it's like Texas, they use sub-crews (Ro-Mexicans). A sub-crew that only does rough-in's, a sub-crew that only trims out, etc

    The EC's don't pay SS or unemployment tax because....well...they are...
  24. Replies
    14$$
    Views
    2,974

    Yes.....you did ...

    Yes.....you did

    https://forums.mikeholt.com/showthread.php?t=195429

    Read all four pages again.
  25. Replies
    14$$
    Views
    2,974

    Didn't you just ask this same question a while...

    Didn't you just ask this same question a while back?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4