Search:

Type: Posts; User: MattS87

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Fancy pin-out

    by MattS87
    Replies
    7$$
    Views
    596

    One of these may work...

    One of these may work https://www.amazon.com/ProsKit-CP-463-Contact-Crimper-4-Indent/dp/B002CCISPS

    we use it for a "DelphiKit" which has similar looking pins.
  2. Thread: Look up.

    by MattS87
    Replies
    13$$
    Views
    4,572

    Yep just a delivery. Where the lines are is well...

    Yep just a delivery. Where the lines are is well enough away from anything of value on my property luckily. Got some nice burn marks in the grass though :)
  3. Replies
    10$$
    Views
    948

    Unfortunately, this company doesn't shell out...

    Unfortunately, this company doesn't shell out money for upgrades until catastrophic failure so I'm stuck with them for now. I have worked in places where they used the PLC 5 racks as remote I/O which...
  4. Thread: Look up.

    by MattS87
    Replies
    13$$
    Views
    4,572

    Had some gravel delivered this morning to my...

    Had some gravel delivered this morning to my house. Last truck had about 1/2 yd left and was to dump it at the back of the property. Turned around as i heard the hum of arcing electrical to see he...
  5. Replies
    10$$
    Views
    948

    An update for any of you interested. This PLC...

    An update for any of you interested. This PLC uses the old AB 6200 software so in order for RSLogix to see the PLC and connect, I had to put it in program mode (normally running 24/7 so had to wait...
  6. Replies
    6$$
    Views
    1,190

    Out of curiosity, have you looked in the...

    Out of curiosity, have you looked in the enclosures where the conduit terminates? It could be that they pulled extra control wires for future use.
  7. Replies
    49$$
    Views
    3,582

    12" x 12"x 1" actual dimension is a board foot....

    12" x 12"x 1" actual dimension is a board foot. Rough cuts are refered to as quarters (4/4, 5/4, 8/4). But a 4/4 board will be planed down to 3/4 and so on
  8. Replies
    49$$
    Views
    3,582

    "call my boss if you don't like my answer", shows...

    "call my boss if you don't like my answer", shows up and sees he was over-ruled :rant:
    But at least you made money on the fix
  9. Replies
    49$$
    Views
    3,582

    1x4's would be sufficient we just happened to...

    1x4's would be sufficient we just happened to have 2x4's laying around from the concrete forms :)
  10. Replies
    16$$
    Views
    1,072

    But if nothing is installed to prevent someone...

    But if nothing is installed to prevent someone from trying to open them at the same time can you use that arguement?
  11. Replies
    16$$
    Views
    1,072

    Since it is a known load on the circuit and not...

    Since it is a known load on the circuit and not just general purpose I would say a calc would have to be done, which would undoubtedly exceed your circuit rating
  12. Replies
    49$$
    Views
    3,582

    Did a similar job last year and had same issue....

    Did a similar job last year and had same issue. Inspector said all they required is to place 2x4s horizontally along the walls where the wiring was so if something fell between stud bays the wiring...
  13. Thread: over current

    by MattS87
    Replies
    11$$
    Views
    725

    Has this always been the case or something new?...

    Has this always been the case or something new? Not sure if it applies here, but since you say this only happens while lowering, I will assume it is drawing the excess current because it is trying to...
  14. Replies
    10$$
    Views
    948

    Not that I see in A-B's documentation. I am using...

    Not that I see in A-B's documentation. I am using these instructions http://literature.rockwellautomation.com/idc/groups/literature/documents/in/1784-in045_-en-p.pdf
  15. Replies
    10$$
    Views
    948

    This is the first time I have tried to connect to...

    This is the first time I have tried to connect to it. Others may have previously but I don't know for sure. The PLC has been in place for some time
  16. Replies
    10$$
    Views
    948

    Can't connect to AB PLC 5/12 controller

    I am trying to connect to an AB PLC 5/12 controller using a 1784-U2DHP adapter. The adapter is configured and according to the lights, it is talking to the DH+ network. In RSLinks I can see node 01...
  17. Replies
    17$$
    Views
    987

    We've adopted the 2017 code now

    We've adopted the 2017 code now
  18. Replies
    17$$
    Views
    987

    AFCI is required, GFCI is not in your case

    AFCI is required, GFCI is not in your case
  19. Replies
    11$$
    Views
    957

    Take a look at this page ...

    Take a look at this page https://www.schneider-electric.us/en/faqs/FA110798/
  20. Replies
    40$$
    Views
    2,451

    Well if you are using a harvester that would be...

    Well if you are using a harvester that would be "cutting" corn in my book :)
  21. Replies
    9$$
    Views
    691

    Your profile says you are a GC. Are you allowed...

    Your profile says you are a GC. Are you allowed to do electrical work in your area?
  22. Thread: Double oven

    by MattS87
    Replies
    13$$
    Views
    854

    The Frigidaire I put in our house a few months...

    The Frigidaire I put in our house a few months ago fed out the bottom but otherwise I did as you describe. As other posters mentioned try to look up install instructions online if you don't have your...
  23. Replies
    32$$
    Views
    3,700

    I have only done something like that once so far....

    I have only done something like that once so far. A nice made in USA kershaw pocket knife. Got down and realized it had fell out in the attic. 12" of fiberglass blown in and all i could say was "I'm...
  24. Replies
    32$$
    Views
    3,700

    I always hate when I get up in the attic, make my...

    I always hate when I get up in the attic, make my way to the fixture, dig out the insulation around it, then realize I left something down below. I also tell myself i will never do anymore remodel...
  25. Replies
    32$$
    Views
    1,724

    The manufacturer of this unit is LG. I just...

    The manufacturer of this unit is LG. I just re-read the install instructions (which suck if you ask me), and it mentions #12 for the feed with 20A fuses which i have. Then i found a section that...
Results 1 to 25 of 182
Page 1 of 8 1 2 3 4