250.24(A)(1) Bonding the grounded conductor.

Status
Not open for further replies.
A

AV8R

Member
Location
Kansas City
We work with multiple POCO's. One will have you bond the grounded conductor in the meter can, another will forbid it. My question is, if we are asked to bond the grounded conductor inside the meter can, are we still obligated to bond the grounded conductor at the main disconnect? Are we permitted to do it? Is it optional? 250.24(A)(1) seems to say it can be done at either location, to and including the the terminal or bus at the main. Am I interpreting that correctly to assume I need to still bond the neutral to the GEC at the main service disconnect?
 
Last edited:
Most meter sockets are designed so that they automatically bond the grounded conductor due to the neutral "buss" being mounted to the can itself. 250.24 still requires you bond the service disconnect. Depending on the wiring method you may actually set up a "objectionable" current but this is accepted by practice.

Your question seems to be discussing the connection of a grounding electrode, not bonding. Unless POCO has a rule, that connection can be made at the meter or service disconnect. IMHO, the connection to a particular electrode should only originate at one of those locations to prevent objectionable flow (other electrodes can connection to the other location)
 
augie47 said:
Most meter sockets are designed so that they automatically bond the grounded conductor due to the neutral "buss" being mounted to the can itself. 250.24 still requires you bond the service disconnect. Depending on the wiring method you may actually set up a "objectionable" current but this is accepted by practice.

Your question seems to be discussing the connection of a grounding electrode, not bonding. Unless POCO has a rule, that connection can be made at the meter or service disconnect. IMHO, the connection to a particular electrode should only originate at one of those locations to prevent objectionable flow (other electrodes can connection to the other location)
Click to expand...

I probably didn't ask the question correctly. We were asked by POCO to attach a grounding electrode to the meter can from a ground rod, and the neutral is also bonded to the meter can at that point. In addition, we still installed all of our grounding at the main disconnect; water main, building steel, concrete encased electrode, ETC. My foreman opted to leave out the bonding jumper between the neutral bar and the equipment ground, just like we would at a sub panel. I asked him to install the jumper at the main, after I inspected the panel. Now I'm second guessing myself and looking for confirmation or correction.
Thanks!
 
AV8R said:
I probably didn't ask the question correctly. We were asked by POCO to attach a grounding electrode to the meter can from a ground rod, and the neutral is also bonded to the meter can at that point. In addition, we still installed all of our grounding at the main disconnect; water main, building steel, concrete encased electrode, ETC. My foreman opted to leave out the bonding jumper between the neutral bar and the equipment ground, just like we would at a sub panel. I asked him to install the jumper at the main, after I inspected the panel. Now I'm second guessing myself and looking for confirmation or correction.
Thanks!
Click to expand...

You were good up to the bold part. You need an MBJ at the panel.
 
infinity said:
You were good up to the bold part. You need an MBJ at the panel.
Click to expand...

That's what I thought, thanks. No matter how many grounding Continuing Ed classes I've taken, I feel like there's so much still to learn about a seemingly small subject, bonding and grounding.
 
AV8R said:
That's what I thought, thanks. No matter how many grounding Continuing Ed classes I've taken, I feel like there's so much still to learn about a seemingly small subject, bonding and grounding.
Click to expand...
I read 250.64(A)(1) and GEC connection has to be accessible location. Utility meter can are locked by the utility and not accessible. Utility may be have special type of enclosure where GEC accessible otherwise GEC meter can wont be accessible.

Sent from my SM-G935U using Tapatalk
 
hhsting said:
I read 250.64(A)(1) and GEC connection has to be accessible location. Utility meter can are locked by the utility and not accessible. Utility may be have special type of enclosure where GEC accessible otherwise GEC meter can wont be accessible.
Click to expand...
Not true, this is a common believed myth, a meter can is accessible or you could not have any connections inside it .

Roger
 
Around here POCO locks the meter can so that no one steal power and meter is only accesible to POCO. I guess every POCO is different.

Sent from my SM-G935U using Tapatalk
 
hhsting said:
Around here POCO locks the meter can so that no one steal power and meter is only accesible to POCO. I guess every POCO is different.
Click to expand...
That doesn't change the fact that it is still accessible, just an inconvenience to have to wait for them to get there.

Roger
 
Defintion NEC accessible: capable of being reached quickly for operation, renewal, or inspections without requiring those to whom ready access is requisite to actions such as to use tools, to climb over or remove obstacles, or to resort to portable ladders and so forth.

One cannot reach quickly have to wait for POCO.
 
hhsting said:
Defintion NEC accessible: capable of being reached quickly for operation, renewal, or inspections without requiring those to whom ready access is requisite to actions such as to use tools, to climb over or remove obstacles, or to resort to portable ladders and so forth.

One cannot reach quickly have to wait for POCO.
Click to expand...
Go back and read Accessible (as applied to wiring methods), you're reading the wrong definition.

Roger
 
AV8R said:
We work with multiple POCO's. One will have you bond the grounded conductor in the meter can, another will forbid it. My question is, if we are asked to bond the grounded conductor inside the meter can, are we still obligated to bond the grounded conductor at the main disconnect? Are we permitted to do it? Is it optional? 250.24(A)(1) seems to say it can be done at either location, to and including the the terminal or bus at the main. Am I interpreting that correctly to assume I need to still bond the neutral to the GEC at the main service disconnect?
Click to expand...

I think the confusion is you are talking about two different things: one is the connection of the GEC to the grounded conductor, the other is the MBJ - the connection of the EGC bus to the grounded conductor.
 
Accessible: admitting close approach; not guarded by locked doors, elevation, or other effective means.

GEC connection applies to meter equipment enclosure.

Sent from my SM-G935U using Tapatalk
 
AV8R said:
I probably didn't ask the question correctly. We were asked by POCO to attach a grounding electrode to the meter can from a ground rod, and the neutral is also bonded to the meter can at that point. In addition, we still installed all of our grounding at the main disconnect; water main, building steel, concrete encased electrode, ETC. My foreman opted to leave out the bonding jumper between the neutral bar and the equipment ground, just like we would at a sub panel. I asked him to install the jumper at the main, after I inspected the panel. Now I'm second guessing myself and looking for confirmation or correction.
Thanks!
Click to expand...

You did the right thing tell him to install the main bonding jumper. Having EGCs not ultimately connected to the grounded conductor is in my judgement a hundred times more dangerous than having the wrong location for connection of a grounding electrode conductor.
 
hhsting said:
Accessible: admitting close approach; not guarded by locked doors, elevation, or other effective means.

GEC connection applies to meter equipment enclosure.

Sent from my SM-G935U using Tapatalk
Click to expand...
You're still reading the wrong definition, read the one I pointed you to. After that if you still can't grasp it tell me why the other conductors landed in the meter can don't need to be accessible.

Just to help you out a little, most commercial buildings (hospitals, shopping centers, schools, etc...) have the electrical rooms locked which takes you away from the definition for Accessible which mean you need to look at Accessible (as applied to wiring methods)

Roger
 
I dont know about other conductors being accessible but 250.24(A)(1) says GEC connection to be accessible.

Why would one use accessible as applied to wiring methods as oppose to accessible as applied to equipment? One needs access to inside meter where GEC is connected.

Sent from my SM-G935U using Tapatalk
 
hhsting said:
I dont know about other conductors being accessible but 250.24(D) says GEC connection to ne accessible.
Click to expand...
All the conductors in a meter can are accessible period, whether or not some clueless POCO has their own rules does not change the NEC definition of ​
Accessible (as applied to wiring methods).

​
hhsting said:
Why would one use accessible as applied to wiring methods as oppose to accessible as applied to equipment?
Click to expand...
Because the wiring in the can is "wiring"

​
hhsting said:
One needs access to inside meter where GEC is connected.
Click to expand...
After being in the trade for more than 40 years I don't know of one single time a GEC needed attention inside a meter can.​

Roger
 
Alright. Just wondering under what circumstances one would use as accessible applied to equipment. Every equipment person wants access to need acces to wiring inside. Why is it even in code.
 
Last edited:
Status
Not open for further replies.
Top