adidas532
Member
- Location
- Augusta, ME
I've been asked to wire a house this summer, my first on the side. Any tips for bidding would be greatly appreciated.
Bidding a house
- Thread starter adidas532
- Start date
- Status
bphgravity
Senior Member
- Location
- Florida
Re: Bidding a house
In my state, this would be against the law.
In my state, this would be against the law.
GG
Senior Member
- Location
- Ft.Worth, T.X.
Re: Bidding a house
My state also. Must have a state masters license, state contractors license, liability insurance, and workmens comp. is optional.
My state also. Must have a state masters license, state contractors license, liability insurance, and workmens comp. is optional.
adidas532
Member
- Location
- Augusta, ME
Re: Bidding a house
I'm pulling the permit. It's still legal to pull a permit with a Journeyman's in MA
I'm pulling the permit. It's still legal to pull a permit with a Journeyman's in MA
adidas532
Member
- Location
- Augusta, ME
Re: Bidding a house
Hey It's worth a try... I'm doing it for a buddy and he wants a good idea what it's going to cost him.
Hey It's worth a try... I'm doing it for a buddy and he wants a good idea what it's going to cost him.
electricmanscott
Senior Member
- Location
- Boston, MA
- Occupation
- Massachusetts Master Electrician, one man show.
Re: Bidding a house
You guys sure are quick to lay down the law. Without any info you assume someone is a diy or your average hack. Wow. 532, Give me a city or town and I will give you more info. Also details on the house itself will help.
[ July 23, 2005, 07:07 AM: Message edited by: electricmanscott ]
You guys sure are quick to lay down the law. Without any info you assume someone is a diy or your average hack. Wow. 532, Give me a city or town and I will give you more info. Also details on the house itself will help.
I don't mind giving out "secrets", there is more than enough work around here for everybody.
[ July 23, 2005, 07:07 AM: Message edited by: electricmanscott ]
GG
Senior Member
- Location
- Ft.Worth, T.X.
Re: Bidding a house
I would start out with a detailed material list, and discuss who will be supplying what. I have been burned on jobs in the past where something wasnt discussed and then Im stuck paying for it.
[ July 23, 2005, 02:16 PM: Message edited by: GG ]
I would start out with a detailed material list, and discuss who will be supplying what. I have been burned on jobs in the past where something wasnt discussed and then Im stuck paying for it.
[ July 23, 2005, 02:16 PM: Message edited by: GG ]
adidas532
Member
- Location
- Augusta, ME
Re: Bidding a house
thank you for all the advice. The house is in the Greenfield MA area.
I just got the prints, I haven't gone over the layout with the homeowner yet. I know the guy and he's pretty understanding, but I don't want to estimate too low and then look bad after.
does the $1 per sq for labor and material cover rough and finish? less the big items.
someone else told me $15 per opening, any thoughts?
Thanks for all your help,
Eric
thank you for all the advice. The house is in the Greenfield MA area.
I just got the prints, I haven't gone over the layout with the homeowner yet. I know the guy and he's pretty understanding, but I don't want to estimate too low and then look bad after.
does the $1 per sq for labor and material cover rough and finish? less the big items.
someone else told me $15 per opening, any thoughts?
Thanks for all your help,
Eric
GG
Senior Member
- Location
- Ft.Worth, T.X.
Re: Bidding a house
The square foot pricing in my opinion is not the way to go. What if the house has 30 can lights, chandeliers, fans in every room on 2 switches, Xmas receptacles in the eves on a time clock, time clock to control the outside landscape lighting, more lights are going outside then inside, doorbell button in the garage, back patio, and front door, light in every closet on a switch, door jam switch in pantry door, under and above kitchen counter lighting. I think you get my point. There is no way that using some magic # and multiplying it by the square footage that your going to come up with an accurate price. Now charging a $ amount per opening doesnt work for me and I dont like it. Some EC's swear by it and have great success with it. The only thing that has worked for me is take off a material list from the blueprints. Once you come up with your material price then apply labor hours, overhead, any other job expenses (ie. permits,tools,etc.), and then you will know what it will cost for you to break even. You then apply the amount of profit you want to make and hopefully you get the job.
[ July 24, 2005, 05:12 PM: Message edited by: GG ]
The square foot pricing in my opinion is not the way to go. What if the house has 30 can lights, chandeliers, fans in every room on 2 switches, Xmas receptacles in the eves on a time clock, time clock to control the outside landscape lighting, more lights are going outside then inside, doorbell button in the garage, back patio, and front door, light in every closet on a switch, door jam switch in pantry door, under and above kitchen counter lighting. I think you get my point. There is no way that using some magic # and multiplying it by the square footage that your going to come up with an accurate price. Now charging a $ amount per opening doesnt work for me and I dont like it. Some EC's swear by it and have great success with it. The only thing that has worked for me is take off a material list from the blueprints. Once you come up with your material price then apply labor hours, overhead, any other job expenses (ie. permits,tools,etc.), and then you will know what it will cost for you to break even. You then apply the amount of profit you want to make and hopefully you get the job.
[ July 24, 2005, 05:12 PM: Message edited by: GG ]
GG
Senior Member
- Location
- Ft.Worth, T.X.
Re: Bidding a house
]
[ July 24, 2005, 05:11 PM: Message edited by: GG ]
]
[ July 24, 2005, 05:11 PM: Message edited by: GG ]
- Status